CEILING FAN CONTROL FOR FREE
CEILING FAN CONTROL HOW TO
CEILING FAN CONTROL INSTALL
CEILING FAN CONTROL MANUAL
CEILING FAN CONTROL FULL

For the system to work, you must purchase a remote receiver (BTR9 or BTR9U) that you install in the canopy of most any pull-chain operated ceiling fan. This app produces IR signals that have been tested on a small sample of ceiling fans.ДЇanSync allows you to control your ceiling fan from your smartphone by pairing them via bluetooth.

CEILING FAN CONTROL FULL

Featuring 3 speed fan controls, full range light kit dimming and timers for fan and light.Д¬eiling Fan Remote uses your deviceвЂ™s Infrared (IR) transmitter to interface with your remote-controlled ceiling fan. This app is only available on the App Store for iOS devices.Д¬ontrol your ceiling fan from your smartphone.

CEILING FAN CONTROL FOR FREE

Download the app for free and start enjoying the convenience of scheduling your fan and light with your smartphone. Put the latest technology to work for you with our SIMPLEconnect app, available for iOS and Android devices. Check wires in fan going to the receiver to be sure all wiring is connected and secure. If not you most likely have a faulty remote control or bad receiver in the ceiling fan and you will need to replace either the remote control or receiver. Once you match up the dip switches with the remote and ceiling fan receiver, the remote should work and control the fan. Be sure to use caution and turn power off to the ceiling fan when checking the ceiling fan remote receiver. If you still have trouble setting the dip switches on the remote, check the receiver in the ceiling fan. Once the dip switches are in the right position, the ceilingВ fan will respond to the remote. Keep testing the different dip switch positions until the ceiling fan works with the remote control. Test this with the fan and see if this works. Slide the first switch in the on position or to 0001.

Test it on the fan to see if it works with the fan. Put all dip switches to off or indicated by 0000. Locate the dip switches under the small panel on your remote control.

CEILING FAN CONTROL HOW TO

How to set the dip switches (settings and programming) on your ceiling fan remote control: See below for how to set the dip switches on your remote control.

It will take 16 combinations to test each setting to try to reactivate your ceiling fan.

If your ceiling fan remote control has 4 dip switches you will need to adjust the switches one by one. Here is a way to get the dip switches in the right position so the remote control can work properly with your ceiling fan. If you have accidentally changed or moved the dip switches on the remote control, the remote will not work and therefore not be able to control the fan to spin or turn on the lights. The receiver is located in the top portion of the fan itself. These switches are located under the battery cover on the remote control and also located on the receiver (depending on the age of fan as some fans do not have a typical receiver). Most ceiling fan remote controls have small switches called dip switches. Programming a Ceiling Fan with Dip Switches To check the remote control dip switches, see belowвЂ¦ You can check the dip switches on the remote control and receiver to be sure they are set correctly. I hope this helps it's really quite simple and gives you great control.If the switch on the wall is turned ON, the remote has fresh batteries and it still does not work, you may either need a replacement remote or receiver. You can also easily utilise a one button fan speed control by using the start/next button on a single action button which is quite nice too. Once you have these sorted you can begin programming your inputs in design.Because you have your sequences assigned you can program these easily without many speeds operating at the same time. I would also have the LED feedback use different blink rates to show some feedback via a keypad. The sequence should look something like this(I'll continue to use the 3 speed and off as an example)

CEILING FAN CONTROL MANUAL

In your manual sequence you'll want to have as many steps as you've wired your capacitor for(this is generally 3 plus one for off) and the obvious stop step which will be all relays open. When designing your loads you'll need one fan load per speed in load types this is listed as fan switched. As for the control in HWQS Designer I've found the best way to control a fan is via a manual sequence, the reason being you only ever want one relay closed at a time otherwise you will have odd speeds or constantly on. What we currently recommend to our customers in Australia is use either a LQSE-4S10-D or a RPM-4R and wire the capacitor included with the fan to control the speed(one relay per speed, except for off which doe).

Ceiling fan control